LIGHTWEIGHT AND LOW PROFILE DESIGN

1 38

LX27 Gen 2 Lightweight Rooftop Tent

$6,750.00

Lightweight Clamshell Rooftop Tent · 81kg · 175mm Closed · 30-Second Setup


The LX27 Gen 2 is the lightest and lowest profile tent in our range: 81kg and just 175mm high when closed, yet it opens to 1.6m of headroom with room for two adults on a 70mm mattress: 30mm of memory foam on top of 40mm of high-density foam. Gas struts lift the aluminium clamshell in about 30 seconds, and standard bedding, sheets and sleeping bags stay stored right inside when you close it. It comes with the Compact Telescopic Ladder with angled steps.


Dimmable tri-colour LED strips, USB-A, USB-C and 12V outlets, and a 100kg dynamic roof rating with Ezi-Slot channels for solar, tracks or an awning. Made in South Africa, with a 2-year conditional warranty.

Read MoreRead More
Submit An Enquiry
SKU:4RTCLX27G2 Find in Store

LX27 Gen 2: our lightest hard shell rooftop tent

The LX27 Gen 2 is built for touring rigs where weight and height matter. At 81kg (without the ladder) and 175mm high when closed, it's the lightest and lowest profile tent we make. That helps with roof load, fuel use, wind noise and garage or car park clearance.

Open it up and, at its highest point, there's 1.6m of headroom, or about 1,520mm measured from the top of the mattress, so two adults can sit up, get changed and sleep comfortably.

Up in 30 seconds

The clamshell closes on our own custom-made, heavy-duty over-centre latches, made from stainless steel, and they have holes for a padlock so you can lock the tent.

Undo them, let the gas struts lift the aluminium clamshell, then slot the 8mm spring steel poles into place to hold the rainfly out over the doors: the whole setup takes about 30 seconds. There's 70mm of clearance above the mattress when it's closed, so standard bedding, sheets and sleeping bags stay stored right inside the closed tent between camps. That saves space in your vehicle and keeps your bedding clean and dust free.

Comfort inside

The 70mm mattress (2.05m long × 1.27m wide) has 30mm of memory foam on top of a 40mm high-density foam base, which gives a firm foundation that resists bottoming out. The two layers are joined together inside a removable, zippered canvas cover, over a marine carpet underlay designed to help reduce condensation beneath the mattress.

  • Doors: large front and side doors make getting in and out of the tent easy. Each has an outer canvas door, an inner canvas door and midge mesh. Every canvas door and midge mesh has YKK spiral zips.
  • Ventilation: the inner canvas doors let you control ventilation from inside the tent without opening the midge mesh screens, and a mesh-covered vent above the rear door keeps air moving when you've closed everything up.
  • Roof storage: two roof pouches and a clear tablet pouch.
  • Side storage: four large canvas side pouches, each with a heavy-duty mesh pouch on the outside, so there are eight side pouches in total. The mesh pouches make it easy to see what's in them, like your phone or keys.
  • Water bottles: two heavy-duty mesh water bottle holders. Together, the pouches keep the small things off the mattress.

Power and light, already wired

  • Lighting: dimmable tri-colour LED strips at the head and foot, with the main control panel at the foot and extra switches at the entrance.
  • Outlets: two USB-A ports, two USB-C ports and two 12V sockets at the foot of the mattress.
  • Power input: from your vehicle through the 50A Anderson plug under the tent, or through the internal 20A WAECO input socket.
  • Optional fan: the Sirocco fan mount plate installs inside the tent on pre-fitted rivnuts in one of the internal beams that reinforce the roof, ready for a Sirocco II 12V fan.
  • Cable channels: zippered canvas channels run up the inside of the roof to keep wiring for fans and lights neatly stored, so nothing gets caught when you close the tent.

Built light, not weak

The frame is our B-Tech® Alloy extruded aluminium with seam-welded corners. Light as it is, it will still carry any of our freestanding awnings, mounted on the tent with the LX27 awning to tent brackets.

The body is dual-layer 260gsm acrylic-treated polyester ripstop canvas, treated against mould, mildew and UV. The two layers work like double glazing: the air gap between them insulates better against heat and cold and significantly reduces condensation build-up on the inside of the tent walls. They also make it a blackout fabric that adds weather resistance and blocks out light, so the tent stays darker at sunrise.

Automotive-grade rubber seals keep the tent dust free and watertight when it's closed.

A large, removable one-piece rainfly with 8mm spring steel poles and adjustable storm straps covers the doors in wet weather.

Why the rainfly matters

  • Dry entry and exit: it covers the ladder and entryway, so you can get in and out safely without getting soaked or bringing dripping water inside.
  • Extra weather protection: it's an extra layer of defence against heavy rain, stopping water pooling directly against the main tent canvas or doorways.
  • Airflow in wet weather: it shields the openings, so you can keep windows or vents cracked open for fresh air without rain splashing inside.

Carry more on top

The internally reinforced roof is rated to 100kg dynamic when closed and 35kg when open, subject to the rating of whatever the tent is mounted to. Ezi-Slot channels in the roof and sides take our accessories without drilling:

As with any roof-mounted gear, add up the tent, your rack or canopy and anything carried on top, and confirm the total is within your vehicle's and rack's dynamic roof load ratings.

Getting in and out

The tent comes with a 2.6m Compact Telescopic Ladder with angled steps and two ladder brackets: one pre-mounted at the open end of the tent, and one you can mount to either side. You can climb in through the open end or from the side, whichever suits your vehicle setup.

Install your tent

The LX27 Gen 2 comes with:

  • six fitment brackets, three for each side, which mount to the side of the foot rails to secure the tent to your load bars
  • two adjustable foot rails, 20mm high, which run the full length of the tent underneath it and don't need to be fitted for every installation

You can fit the tent the usual way, with the open end at the rear of the vehicle, or in reverse, with the open end facing forward and the ladder secured to a roof rack on the cab. If you fit it in reverse, the Rooftop Tent Dead Bolt Bracket is required, for extra protection against the tent opening while you're driving.

See our rooftop tent mounting options for canopies and low-profile setups. The Bush Company or one of our stockists can fit it, or you can follow the fitting instructions in the Installation tab.

Is the LX27 Gen 2 right for you?

Choose it if you want the lightest, lowest profile hard shell we make.

  • For extra room for bulkier bedding such as thick doonas, and 1.7m of headroom at the entry, look at the AX27 Clamshell Rooftop Tent.
  • For near-full headroom from end to end, the double-action TX27 and TX27 MAX are the step up.

Watch the LX27 Gen 2 product video for a full walkthrough of the tent.

Made in South Africa for The Bush Company, with a 2-year conditional warranty. Buy online, pick up the same day from our showroom in Marcoola on the Sunshine Coast, or order through one of our stockists Australia wide.

Description

LX27 Gen 2: our lightest hard shell rooftop tent

The LX27 Gen 2 is built for touring rigs where weight and height matter. At 81kg (without the ladder) and 175mm high when closed, it's the lightest and lowest profile tent we make. That helps with roof load, fuel use, wind noise and garage or car park clearance.

Open it up and, at its highest point, there's 1.6m of headroom, or about 1,520mm measured from the top of the mattress, so two adults can sit up, get changed and sleep comfortably.

Up in 30 seconds

The clamshell closes on our own custom-made, heavy-duty over-centre latches, made from stainless steel, and they have holes for a padlock so you can lock the tent.

Undo them, let the gas struts lift the aluminium clamshell, then slot the 8mm spring steel poles into place to hold the rainfly out over the doors: the whole setup takes about 30 seconds. There's 70mm of clearance above the mattress when it's closed, so standard bedding, sheets and sleeping bags stay stored right inside the closed tent between camps. That saves space in your vehicle and keeps your bedding clean and dust free.

Comfort inside

The 70mm mattress (2.05m long × 1.27m wide) has 30mm of memory foam on top of a 40mm high-density foam base, which gives a firm foundation that resists bottoming out. The two layers are joined together inside a removable, zippered canvas cover, over a marine carpet underlay designed to help reduce condensation beneath the mattress.

  • Doors: large front and side doors make getting in and out of the tent easy. Each has an outer canvas door, an inner canvas door and midge mesh. Every canvas door and midge mesh has YKK spiral zips.
  • Ventilation: the inner canvas doors let you control ventilation from inside the tent without opening the midge mesh screens, and a mesh-covered vent above the rear door keeps air moving when you've closed everything up.
  • Roof storage: two roof pouches and a clear tablet pouch.
  • Side storage: four large canvas side pouches, each with a heavy-duty mesh pouch on the outside, so there are eight side pouches in total. The mesh pouches make it easy to see what's in them, like your phone or keys.
  • Water bottles: two heavy-duty mesh water bottle holders. Together, the pouches keep the small things off the mattress.

Power and light, already wired

  • Lighting: dimmable tri-colour LED strips at the head and foot, with the main control panel at the foot and extra switches at the entrance.
  • Outlets: two USB-A ports, two USB-C ports and two 12V sockets at the foot of the mattress.
  • Power input: from your vehicle through the 50A Anderson plug under the tent, or through the internal 20A WAECO input socket.
  • Optional fan: the Sirocco fan mount plate installs inside the tent on pre-fitted rivnuts in one of the internal beams that reinforce the roof, ready for a Sirocco II 12V fan.
  • Cable channels: zippered canvas channels run up the inside of the roof to keep wiring for fans and lights neatly stored, so nothing gets caught when you close the tent.

Built light, not weak

The frame is our B-Tech® Alloy extruded aluminium with seam-welded corners. Light as it is, it will still carry any of our freestanding awnings, mounted on the tent with the LX27 awning to tent brackets.

The body is dual-layer 260gsm acrylic-treated polyester ripstop canvas, treated against mould, mildew and UV. The two layers work like double glazing: the air gap between them insulates better against heat and cold and significantly reduces condensation build-up on the inside of the tent walls. They also make it a blackout fabric that adds weather resistance and blocks out light, so the tent stays darker at sunrise.

Automotive-grade rubber seals keep the tent dust free and watertight when it's closed.

A large, removable one-piece rainfly with 8mm spring steel poles and adjustable storm straps covers the doors in wet weather.

Why the rainfly matters

  • Dry entry and exit: it covers the ladder and entryway, so you can get in and out safely without getting soaked or bringing dripping water inside.
  • Extra weather protection: it's an extra layer of defence against heavy rain, stopping water pooling directly against the main tent canvas or doorways.
  • Airflow in wet weather: it shields the openings, so you can keep windows or vents cracked open for fresh air without rain splashing inside.

Carry more on top

The internally reinforced roof is rated to 100kg dynamic when closed and 35kg when open, subject to the rating of whatever the tent is mounted to. Ezi-Slot channels in the roof and sides take our accessories without drilling:

As with any roof-mounted gear, add up the tent, your rack or canopy and anything carried on top, and confirm the total is within your vehicle's and rack's dynamic roof load ratings.

Getting in and out

The tent comes with a 2.6m Compact Telescopic Ladder with angled steps and two ladder brackets: one pre-mounted at the open end of the tent, and one you can mount to either side. You can climb in through the open end or from the side, whichever suits your vehicle setup.

Install your tent

The LX27 Gen 2 comes with:

  • six fitment brackets, three for each side, which mount to the side of the foot rails to secure the tent to your load bars
  • two adjustable foot rails, 20mm high, which run the full length of the tent underneath it and don't need to be fitted for every installation

You can fit the tent the usual way, with the open end at the rear of the vehicle, or in reverse, with the open end facing forward and the ladder secured to a roof rack on the cab. If you fit it in reverse, the Rooftop Tent Dead Bolt Bracket is required, for extra protection against the tent opening while you're driving.

See our rooftop tent mounting options for canopies and low-profile setups. The Bush Company or one of our stockists can fit it, or you can follow the fitting instructions in the Installation tab.

Is the LX27 Gen 2 right for you?

Choose it if you want the lightest, lowest profile hard shell we make.

  • For extra room for bulkier bedding such as thick doonas, and 1.7m of headroom at the entry, look at the AX27 Clamshell Rooftop Tent.
  • For near-full headroom from end to end, the double-action TX27 and TX27 MAX are the step up.

Watch the LX27 Gen 2 product video for a full walkthrough of the tent.

Made in South Africa for The Bush Company, with a 2-year conditional warranty. Buy online, pick up the same day from our showroom in Marcoola on the Sunshine Coast, or order through one of our stockists Australia wide.

Specifications
  • Style: aluminium hard shell clamshell, gas-strut assisted
  • Setup: about 30 seconds
  • Weight: 81kg, excluding the ladder and the foot rails (3.4kg for the pair)
  • External dimensions (closed): 2.25m L (2.32m including hinges and handles) × 1.39m W (1.45m including gas struts)
  • Closed height: 175mm; 195mm with the 20mm foot rails fitted
  • Internal headroom at the highest point: 1.6m, or about 1,520mm above the mattress
  • Mattress: 2.05m L × 1.27m W × 70mm thick: 30mm memory foam on top of a 40mm high-density foam base (a firm foundation that resists bottoming out), joined together inside a removable zippered canvas cover; marine carpet underlay to help reduce condensation under the mattress
  • Sleeps: two adults
  • Bedding clearance when closed: 70mm; standard bedding, sheets and sleeping bags stay stored inside
  • Canvas: dual-layer 260gsm acrylic-treated polyester ripstop canvas; mould, mildew and UV resistant; the air gap between the layers works like double glazing for better insulation and significantly less condensation on the inside of the tent walls; blackout fabric for weather resistance and light blocking
  • Frame: B-Tech® Alloy extruded aluminium, seam-welded corners
  • Seals: automotive-grade rubber seals keep the tent dust free and watertight when closed
  • Access: large front and side doors, each with an inner and outer canvas door and midge mesh; every canvas door and midge mesh has YKK spiral zips
  • Ventilation: 3 doors/windows plus a mesh-covered airflow vent above the rear door; the inner canvas doors let you control airflow from inside without opening the midge mesh
  • Power: two USB-A, two USB-C and two 12V sockets at the foot of the mattress
  • Power input: external 50A Anderson plug under the tent, or internal 20A WAECO socket
  • Lighting: pre-wired dimmable tri-colour LED strips at the head and foot; control panel at the foot, switches at the entrance
  • Storage: two roof pouches and a clear tablet pouch; four large canvas side pouches, each with a heavy-duty mesh pouch on the outside (eight side pouches in total); two heavy-duty mesh water bottle holders
  • Cable management: zippered canvas channels up the inside of the roof keep fan and light wiring neatly stored and clear when closing the tent
  • Roof load: 100kg dynamic when closed, 35kg when open, subject to the rating of what the tent is mounted to
  • Accessory mounting: Ezi-Slot channels in the roof and sides
  • Rainfly: large, removable, one-piece, with 8mm spring steel poles and adjustable storm straps; keeps the ladder and entry dry for getting in and out, adds a layer of protection against heavy rain and pooling water, and lets you keep windows or vents open in wet weather
  • Latches: custom-made, heavy-duty stainless steel over-centre latches, with holes for a padlock
  • Installation: normal (open end to the rear of the vehicle) or reversed (open end facing forward, ladder secured to a cab roof rack); reversed installation requires the Rooftop Tent Dead Bolt Bracket
  • Warranty: 2 years conditional
  • Made in South Africa

What’s included?

  • Six fitment brackets (three per side) that mount to the side of the foot rails for securing to load bars
  • Two adjustable foot rails, 20mm high and running the full length of the tent (not needed for every installation)
  • 2.6m Compact Telescopic Ladder with angled steps
  • Two ladder brackets (one pre-mounted at the open end, one for either side)
  • Large removable one-piece rainfly with 8mm spring steel poles and adjustable storm straps
  • Pre-wired LED light strips

Installation

Download a copy of the fitting instructions from our Guides and Fitment Instructions page.

The Bush Company or one of our stockists can assemble and install your rooftop tent.

If you choose to install the rooftop tent yourself please make sure that you have done the due diligence on your intended installation to ensure that it does not create any safety issues. Please ensure that you follow standard safety precautions when undertaking the installation.

If you are installing the rooftop tent yourself, please watch our Pre-Install Assembly video to get some important tips.

Care & Maintenance

Rooftop Tent Care and Maintenance

We recommend that new rooftop tents are opened and the canvas wet down on the outside before first use. Do not spray water onto the air vent above the rear door. This will ensure that your rooftop tent performs flawlessly in wet weather by allowing the poly/cotton core spun thread and canvas to swell ensuring the take up of any potential leaks in the stitching.

Regular Maintenance

  • Lubricate the tent seal with silicon gel and clean seal mating surface thoroughly to prevent the seal from 'sticking' to the tent frame.
  • Check for any signs of wear and tear, such as cracks, tears, or loose stitching in the tent fabric, midge mesh and seals.
  • Inspect zippers, gas struts, hinges for smooth operation and lubrication.

Cleaning Canvas:

  • Do not use soap or detergents on the canvas.
  • Do not store the product if wet, allow drying first.
  • To clean use a soft brush and cold water.
  • Do not expose to petrol, oils or harsh chemicals.

Cleaning Mould From Canvas:

The canvas of The Bush Company Tents is treated during manufacturing with a mould and mildew inhibitor, but in the event that your tent canvas develops mould please follow the steps below to remove it:

  • Allow mould to dry
  • Remove surface mould off with a stiff bristle brush
  • Vacuum the area
  • Treat area with Oil of Clove spray (diluted spray can be purchased or can be mixed using a few drops of oil into a spray bottle of water)

Condensation:

Condensation is a natural occurrence, the combination of cold nights and warm days can create a lovely environment for mould and mildew to develop. This is not because of bad seals but from temperature changes combined with humidity creating condensation inside the tent.

When in use, reduce condensation build-up, keep some of the windows open to increase airflow.

After your trip, make sure you allow the tent to fully dry inside and out. If you are not using your rooftop tent for an extended time (more than 10 days) open the tent regularly to air it out, and possibly remove the mattress and store it separately until your next trip.

Tent Frame Care

To ensure the longevity and aesthetic appeal of your powder coated surfaces, regular care and maintenance are essential. Factors such as pollution, dirt, salt, and exposure to strong ultraviolet (UV) light can gradually impact the quality and integrity of the coating over time.

Cleaning Recommendations:

  • Remove Loose Dirt: Begin by gently removing any loose dirt or deposits from the surface using a wet sponge. This initial step helps prevent scratching during the cleaning process.
  • Use Mild Cleaning Solutions: for general cleaning, utilize a non-abrasive brush or cloth along with a ph-neutral car wash product such as Rig Wash from Revival Offroad to keep the surface of the tent if good condition. These solutions effectively remove dust, salt, and other deposits without causing damage to the powder coating.
  • Rinse Thoroughly: after applying the cleaning solution, rinse the surface thoroughly with clean water. This step ensures the removal of any residue or cleaning agents that may be left behind. 

Powder Coat Treatment

We recommend that at a minimum of once every six months or if your powder coat surface is fading, the powder coat should be treated with a dedicated powder coat restorer such as Rig Revive. Follow the application directions on the product you select.

Recommended Cleaning Frequency:

  • For general use we recommend cleaning and powder coat treatment every six months as a good practice to maintain appearance and coating integrity.
  • If your tent is used regularly for beach camping we recommend cleaning the tent after each trip as you should your vehicle.
  • If your tent is located in an area with high exposure to pollutants or intense UV radiation from being outside all the time, it should be cleaned and the powder coat treated approximately every three months.

 Important Considerations

Avoid Harsh Detergents: Steer clear of detergents that recommend the use of gloves when handling, as they are usually harsh and may be unsuitable for cleaning powder coatings. Instead, opt for a good quality car wash and wax or a similar mild cleaning solution.

Caution with Solvents

While certain solvents are recommended for removing sealants or other building residues, they can potentially harm the extended life of the powder coated surface. To minimise risks, it is best to avoid using solvents unless absolutely necessary. If paint splashes, sealants, or other residues need to be removed, you can safely use methylated spirits, turpentine, or white spirits. However, be cautious as their use may still have long-term effects that may not be immediately visible and could take up to twelve months to appear.

Powder Coat Paint Repair

If the powder coat surface of your tent is damaged and needs to be touched up we recommend the following:

 

Shipping

We aim to offer our customers the most competitive rates for shipping based on the items ordered. Shipping rates at checkout are calculated automatically based on the items ordered and the shipping address. All shipping rates automatically include in-transit insurance from the time of collection to delivery.

Freight Partners Used

Australia Post - orders not including items over 1.05m and/or 20kg in Australia and overseas.

FEDEX - courier delivery to home, business or depot within Australia & overseas.

DHL Express - courier delivery for international orders with items over 1.05m or 20kg.

Off-Grid Power Products

Off-Grid Power products (18V to 12V power supplies, Starlink Mini power kits, in-vehicle battery chargers, USB-C and 12V chargers, and leads) ship direct from our Australian warehouse partner, usually within one business day of your order. Delivery usually takes 1 to 6 business days, depending on where you are.

  • Shipping is free within Australia when your Off-Grid Power items total over $200. Below that, shipping is calculated at checkout.
  • If your order also includes other Bush Company products, those ship separately from Marcoola, so you may receive more than one parcel and see more than one shipping charge.
  • Off-Grid Power products are only available for delivery within Australia, and can't be collected from our Marcoola showroom.

Home Delivery

If you provide a residential address for delivery of your order, it is assumed that your items can be left in a safe place at your home if nobody is available to receive them in person, in which case The Bush Company is not accountable for any loss once delivery is made.

Pickup In-Store

To save on shipping costs you can select "Pickup In-Store" during checkout.

All items, including CapRax Canopies by Rhinoman, are available for collection from our showroom at The Bush Company, 14 Cessna Street, Marcoola, QLD 4564, except Off-Grid Power products, which are delivered from our warehouse partner. In-stock orders are usually ready for collection the same day. We will contact you to confirm when your order is ready to collect.

Please note that due to insurance and health and safety issues, you cannot self-fit your purchase on our premises.

International Delivery

Freight costs for international orders are calculated excluding customs duties and local sales taxes. The receiver will be required to cover the costs of local import duties and sales taxes. International delivery is available through our website for all items excluding rooftop tents, awnings and ute canopies. To obtain a freight quote for the delivery of these items overseas, please contact us by email at info@thebushcompany.com.au or by phone on +61 (07) 5302 6948.

Off-Grid Power products are not available for international delivery.

Large Items (Courier Delivery Tents & Canopies)

Home Delivery

'Home Delivery' means a home or private residence, including locations where a business is operated from the home or private residence. For home delivery of rooftop tents and canopies a forklift must be available at the delivery point, with truck access. We will contact you to confirm that this is the case. Unloading by hand is not permitted by the couriers due to health and safety regulations. If, as is usually the case, you do not have a forklift available at your home address, we can arrange for your tent or canopy to be delivered to the nearest FEDEX freight depot/agent for collection from there.

Business Delivery

If you provide a commercial premises address for the delivery of your rooftop tent or canopy, a forklift must be available at the delivery point, with truck access. Unloading by hand is not permitted by the couriers due to health and safety regulations.

Depot Collection

If you want to have your items delivered to a depot for you to collect (often the cheapest option for tents and canopies) but you are unsure of the nearest depot, please contact us by email at info@thebushcompany.com.au or by phone on +61 (07) 5302 6948 to obtain a shipping quote and place your order.

If you have any questions regarding shipping, please contact us by email at info@thebushcompany.com.au or by phone on +61 (07) 5302 6948.

Damage In Transit

If you or the person responsible for receiving your order does not check that the item has arrived in good condition prior to accepting it, The Bush Company cannot be held responsible for any claim for damage in transit.

When your order shipment arrives, it is essential that you check it thoroughly for any signs of damage before signing to accept the shipment. This means checking the exterior box and, if there are any signs of damage externally, the box should be opened and the product examined for any signs of damage to the product itself. This needs to be done before you sign anything to say that the item has been received; the driver needs to wait until you are satisfied. If you are not satisfied with the condition of the item, then you are entitled to refuse delivery and the courier will have to return the product to us.

If you do not follow this procedure and it turns out that the item has been damaged in transit, then there is no way for The Bush Company to claim on the freight insurance to cover any damage. If you sign anything and are not satisfied, you must ensure that this is noted by the driver in writing and obtain a copy that is signed by the driver.

Merchandise Shipping

Our merchandise range (T-shirts, Hoodies, Hats, Mugs etc.) are print on demand products and have different shipping policies associated with them. Please view the 'Delivery & Returns' tab on each product for more information.

Stacked with features

COMPACT, LIGHT AND COMFORTABLE

The LX27 Gen 2 is our low-profile touring tent: just 175mm high when closed and 81kg without the ladder. Inside, 30mm of memory foam sits on a 40mm high-density foam base that resists bottoming out, making for a comfortable night, and standard bedding, sheets and sleeping bags stay stored right inside when you latch it closed. With 1.6m of headroom at the highest point, there's plenty of room to sit up and move around.

ROOM ON TOP, FOR MORE ADVENTURES

The internally reinforced roof is rated to 100kg dynamic when closed, so you can carry solar panels, boards or recovery tracks, and it will still open with 35kg on top. Ezi-Slot channels in the roof and sides take our accessories without drilling. As with any roof-mounted gear, check the total is within your vehicle's and rack's dynamic roof load ratings.

BUILT LIGHT, NOT WEAK

The frame is our B-Tech® Alloy extruded aluminium with seam-welded corners, and light as it is, it will still carry any awning in our range. The body is dual-layer 260gsm acrylic-treated polyester ripstop canvas: the air gap between the layers works like double glazing to insulate and significantly reduce condensation on the inside walls, and the blackout fabric resists the weather and blocks light. A large rainfly with 8mm spring steel poles and adjustable storm straps covers the doors in wet weather.

UP IN 30 SECONDS

Undo the custom-made, heavy-duty stainless steel over-centre latches, let the gas struts lift the clamshell and slot in the spring steel poles to set the rainfly: the LX27 Gen 2 is ready for the night in about 30 seconds. Leave your bedding, sheets and sleeping bags inside when you pack up, and keep the space in your 4WD for everything else.

THE PIONEER’S CHOICE

Built for those who don’t follow the map but write it, the Bush Company’s Rooftop Tents are the gear serious pioneers rely on. Made in South Africa, they’ve earned a reputation as the real deal—proven in the harshest conditions and respected by overlanders worldwide. This is not just a tent; it’s a long-term investment in every adventure you'll ever take.

LX27 Gen 2 Lightweight Rooftop Tent VIDEOS

View all

FAQS

How much does the LX27 Gen 2 Rooftop Tent weigh?

About 81kg (178.6 lb), excluding the ladder and the foot rails, which weigh 3.4kg (7.5 lb) for the pair.

What are the dimensions of the LX27 Gen 2?

Closed, it's 2.25m (7'4.6") long, 1.39m (4'6.7") wide and 175mm (6.9in) high, or 195mm (7.7in) high with the 20mm (0.8in) foot rails fitted. Including the hinges, handles and gas struts, it measures 2.32m (7'7.3") by 1.45m (4'9.1").

Open, at its highest point, it gives 1.6m (5'3") of headroom, or about 1,520mm (4'11.8") above the mattress. The mattress is 2.05m (6'8.7") long, 1.27m (4'2") wide and 70mm (2.8in) thick.

How much can I carry on the roof?

The roof is rated to 100kg (220.5 lb) dynamic when the tent is closed and 35kg (77.2 lb) when it's open, subject to the rating of whatever the tent is mounted to. As with any roof-mounted gear, add up the tent, your rack or canopy and anything on top, and confirm the total is within your vehicle's and rack's dynamic roof load ratings.

Can I leave bedding inside?

Yes. There's 70mm (2.8in) of clearance above the mattress when the tent is closed, so standard bedding, sheets and sleeping bags stay stored right inside. For bulkier bedding such as thick doonas, the AX27 and the TX27 range have more room.

Is there a video of the LX27 Gen 2?

Yes. Our LX27 Gen 2 product video walks through the tent in detail, including its dimensions, canvas, mattress, power and lighting, mounting rails and ladder.

How do I install or mount the LX27 Gen 2?

It comes with six fitment brackets, three for each side, which mount to the side of the foot rails to secure the tent to load bars. The two adjustable foot rails don't need to be fitted for every installation, and we have other mounting options for roof racks and canopies. The Bush Company or one of our stockists can fit it for you. If you're fitting it yourself, follow the rooftop tent fitting instructions and watch our Pre-Install Assembly video first.

Didn’t find your answer?

Don't hesitate to contact us

LX27 Gen 2 Lightweight Rooftop Tent open on a Land Cruiser 76 Series wagon, rainfly out
The Bush Company

LX27 Gen 2 Lightweight Rooftop Tent

$6,750.00

LX27 Gen 2: our lightest hard shell rooftop tent

The LX27 Gen 2 is built for touring rigs where weight and height matter. At 81kg (without the ladder) and 175mm high when closed, it's the lightest and lowest profile tent we make. That helps with roof load, fuel use, wind noise and garage or car park clearance.

Open it up and, at its highest point, there's 1.6m of headroom, or about 1,520mm measured from the top of the mattress, so two adults can sit up, get changed and sleep comfortably.

Up in 30 seconds

The clamshell closes on our own custom-made, heavy-duty over-centre latches, made from stainless steel, and they have holes for a padlock so you can lock the tent.

Undo them, let the gas struts lift the aluminium clamshell, then slot the 8mm spring steel poles into place to hold the rainfly out over the doors: the whole setup takes about 30 seconds. There's 70mm of clearance above the mattress when it's closed, so standard bedding, sheets and sleeping bags stay stored right inside the closed tent between camps. That saves space in your vehicle and keeps your bedding clean and dust free.

Comfort inside

The 70mm mattress (2.05m long × 1.27m wide) has 30mm of memory foam on top of a 40mm high-density foam base, which gives a firm foundation that resists bottoming out. The two layers are joined together inside a removable, zippered canvas cover, over a marine carpet underlay designed to help reduce condensation beneath the mattress.

Power and light, already wired

Built light, not weak

The frame is our B-Tech® Alloy extruded aluminium with seam-welded corners. Light as it is, it will still carry any of our freestanding awnings, mounted on the tent with the LX27 awning to tent brackets.

The body is dual-layer 260gsm acrylic-treated polyester ripstop canvas, treated against mould, mildew and UV. The two layers work like double glazing: the air gap between them insulates better against heat and cold and significantly reduces condensation build-up on the inside of the tent walls. They also make it a blackout fabric that adds weather resistance and blocks out light, so the tent stays darker at sunrise.

Automotive-grade rubber seals keep the tent dust free and watertight when it's closed.

A large, removable one-piece rainfly with 8mm spring steel poles and adjustable storm straps covers the doors in wet weather.

Why the rainfly matters

Carry more on top

The internally reinforced roof is rated to 100kg dynamic when closed and 35kg when open, subject to the rating of whatever the tent is mounted to. Ezi-Slot channels in the roof and sides take our accessories without drilling:

As with any roof-mounted gear, add up the tent, your rack or canopy and anything carried on top, and confirm the total is within your vehicle's and rack's dynamic roof load ratings.

Getting in and out

The tent comes with a 2.6m Compact Telescopic Ladder with angled steps and two ladder brackets: one pre-mounted at the open end of the tent, and one you can mount to either side. You can climb in through the open end or from the side, whichever suits your vehicle setup.

Install your tent

The LX27 Gen 2 comes with:

You can fit the tent the usual way, with the open end at the rear of the vehicle, or in reverse, with the open end facing forward and the ladder secured to a roof rack on the cab. If you fit it in reverse, the Rooftop Tent Dead Bolt Bracket is required, for extra protection against the tent opening while you're driving.

See our rooftop tent mounting options for canopies and low-profile setups. The Bush Company or one of our stockists can fit it, or you can follow the fitting instructions in the Installation tab.

Is the LX27 Gen 2 right for you?

Choose it if you want the lightest, lowest profile hard shell we make.

Watch the LX27 Gen 2 product video for a full walkthrough of the tent.

Made in South Africa for The Bush Company, with a 2-year conditional warranty. Buy online, pick up the same day from our showroom in Marcoola on the Sunshine Coast, or order through one of our stockists Australia wide.

View product

  • 2-Year Warranty

    Adventure confidently.

  • Engineered to Last

    Exclusive B-Tech® Alloy Extrusion Technology

  • Made in South Africa

    Australian Owned, Tested Globally.

  • Online Support Centre

    Expert Help and Advice.